editLinux version 2.6.18-53.el5 (mockbuild@builder6.centos.org) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-14)) #1 SMP Mon Nov 12 02:14:55 EST 2007
Command line: ro root=LABEL=/1 rhgb quiet console=ttyS0,9600 console=tty
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 00000000bfeb2000 (usable)
BIOS-e820: 00000000bfeb2000 - 00000000bfec8000 (reserved)
BIOS-e820: 00000000bfec8000 - 00000000bfee7c00 (ACPI data)
BIOS-e820: 00000000bfee7c00 - 00000000c0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000240000000 (usable)
DMI 2.5 present.
ACPI: RSDP (v002 DELL ) @ 0x00000000000f2ac0
ACPI: XSDT (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000000f2b48
ACPI: FADT (v003 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000000f2c60
ACPI: MADT (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000000f2d54
ACPI: SPCR (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000000f2dd3
ACPI: HPET (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000000f2e23
ACPI: MCFG (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000000f2e5b
ACPI: WD__ (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000000f2e97
ACPI: SLIC (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000000f2fcb
ACPI: ERST (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000bfeca6c8
ACPI: HEST (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000bfeca8d8
ACPI: BERT (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000bfeca548
ACPI: EINJ (v001 DELL PE_SC3 0x00000001 DELL 0x00000001) @ 0x00000000bfeca578
ACPI: DSDT (v001 DELL PE_SC3 0x00000001 INTL 0x20050624) @ 0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-0000000240000000
Bootmem setup node 0 0000000000000000-0000000240000000
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
On node 0 totalpages: 2063226
DMA zone: 2704 pages, LIFO batch:0
DMA32 zone: 767722 pages, LIFO batch:31
Normal zone: 1292800 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Processor #2 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3 6:15 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x05] address[0xfec10000] gsi_base[32])
IOAPIC[1]: apic_id 5, version 32, address 0xfec10000, GSI 32-55
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a301 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 00000000000a0000 - 0000000000100000
Nosave address range: 00000000bfeb2000 - 00000000bfec8000
Nosave address range: 00000000bfec8000 - 00000000bfee7000
Nosave address range: 00000000bfee7000 - 00000000bfee8000
Nosave address range: 00000000bfee8000 - 00000000c0000000
Nosave address range: 00000000c0000000 - 00000000e0000000
Nosave address range: 00000000e0000000 - 00000000f0000000
Nosave address range: 00000000f0000000 - 00000000fe000000
Nosave address range: 00000000fe000000 - 0000000100000000
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
SMP: Allowing 4 CPUs, 0 hotplug CPUs
Built 1 zonelists. Total pages: 2063226
Kernel command line: ro root=LABEL=/1 rhgb quiet console=ttyS0,9600 console=tty
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x1c3b000 - 0x5c3b000
Memory: 8171652k/9437184k available (2434k kernel code, 215236k reserved, 1235k data, 192k init)
Calibrating delay using timer specific routine.. 5337.14 BogoMIPS (lpj=2668570)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM1)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 16667269
Detected 16.667 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5333.63 BogoMIPS (lpj=2666816)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU X3230 @ 2.66GHz stepping 0b
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x2
Initializing CPU#2
Calibrating delay using timer specific routine.. 5333.47 BogoMIPS (lpj=2666735)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU2: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU X3230 @ 2.66GHz stepping 0b
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 5333.48 BogoMIPS (lpj=2666743)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU3: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU X3230 @ 2.66GHz stepping 0b
Brought up 4 CPUs
testing NMI watchdog ... OK.
time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
time.c: Detected 2666.764 MHz processor.
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
migration_cost=20,3581
checking if image is initramfs... it is
Freeing initrd memory: 2446k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: PXH quirk detected, disabling MSI for SHPC device
Boot video device is 0000:04:02.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBE0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBE0.PXHA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBE4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBE5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 *6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0, 0
hpet0: 4 64-bit timers, 14318180 Hz
PCI-GART: No AMD northbridge found.
pnp: 00:08: ioport range 0x800-0x87f could not be reserved
pnp: 00:08: ioport range 0x880-0x8bf has been reserved
pnp: 00:08: ioport range 0x8c0-0x8df has been reserved
pnp: 00:08: ioport range 0x8e0-0x8e3 has been reserved
pnp: 00:08: ioport range 0x900-0x900 has been reserved
pnp: 00:08: ioport range 0xc00-0xc0f has been reserved
pnp: 00:08: ioport range 0xc10-0xc1f has been reserved
pnp: 00:08: ioport range 0xca0-0xca7 has been reserved
pnp: 00:09: ioport range 0xca8-0xca8 has been reserved
pnp: 00:09: ioport range 0xcac-0xcac has been reserved
PCI: Bridge: 0000:00:01.0
IO window: e000-efff
MEM window: dfa00000-dfbfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:03:02.0
IO window: d000-dfff
MEM window: dfc00000-dfcfffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:02:00.0
IO window: d000-dfff
MEM window: dfc00000-dfcfffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1c.0
IO window: d000-dfff
MEM window: dfc00000-dfcfffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1c.4
IO window: disabled.
MEM window: dfd00000-dfdfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: disabled.
MEM window: dfe00000-dfefffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: dff00000-dfffffff
PREFETCH window: d0000000-d7ffffff
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.4 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1202361847.349:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key FA719CFD42DF8150
- User ID: CentOS (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie03]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
Allocate Port Service[0000:00:1c.5:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: Device 00:07 activated.
00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
GSI 18 sharing vector 0xE1 and IRQ 18
ACPI: PCI Interrupt 0000:04:04.1[B] -> GSI 34 (level, low) -> IRQ 225
0000:04:04.1: ttyS2 at I/O 0xd8c0 (irq = 225) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SiI680: IDE controller at PCI slot 0000:04:07.0
GSI 19 sharing vector 0xE9 and IRQ 19
ACPI: PCI Interrupt 0000:04:07.0[A] -> GSI 32 (level, low) -> IRQ 233
SiI680: chipset revision 2
SiI680: BASE CLOCK == 133
SiI680: 100% native mode on irq 233
ide0: MMIO-DMA , BIOS settings: hda:pio, hdb:pio
ide1: MMIO-DMA , BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: VIRTUALFLOPPY DRIVE Floppy, ATAPI FLOPPY drive
hdb: VIRTUALCDROM DRIVE, ATAPI CD/DVD-ROM drive
hda: set_drive_speed_status: status=0x40 { DriveReady }
hdb: set_drive_speed_status: status=0x40 { DriveReady }
ide0 at 0xffffc20000002f80-0xffffc20000002f87,0xffffc20000002f8a on irq 233
Probing IDE interface ide1...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
hda: -1554408kB, 16577/1/129 CHS, 7616 kBps, 65535 sector size, 385 rpm
hda: The disk reports a capacity of 0 bytes, but the drive only handles -1591714113
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 192k freed
Write protecting the kernel read-only data: 468k
USB Universal Host Controller Interface driver v3.0
GSI 20 sharing vector 0x32 and IRQ 20
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 50, io base 0x0000bc60
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
GSI 21 sharing vector 0x3A and IRQ 21
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 58, io base 0x0000bc80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 50, io base 0x0000bca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 50
usb 1-1: new full speed USB device using uhci_hcd and address 2
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 50, io mem 0xdf9ffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
hda: Invalid capacity for disk in drive
hda: 65471kB, 65535/255/255 CHS, 8191 kBps, 65535 sector size, 65535 rpm
SCSI subsystem initialized
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SAS Host driver 3.04.04
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
mptbase: Initiating ioc0 bringup
ioc0: SAS1068E: Capabilities={Initiator}
PCI: Setting latency timer of device 0000:01:00.0 to 64
usb 4-5: new high speed USB device using ehci_hcd and address 4
usb 4-5: configuration #1 chosen from 1 choice
hub 4-5:1.0: USB hub found
hub 4-5:1.0: 4 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
input: Dell DRAC4 as /class/input/input0
input: USB HID v1.10 Keyboard [Dell DRAC4] on usb-0000:00:1d.0-1
input: Dell DRAC4 as /class/input/input1
input: USB HID v1.10 Mouse [Dell DRAC4] on usb-0000:00:1d.0-1
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
input: Avocent Dell 03R874 as /class/input/input2
input: USB HID v1.10 Keyboard [Avocent Dell 03R874] on usb-0000:00:1d.1-2
input: Avocent Dell 03R874 as /class/input/input3
input: USB HID v1.10 Mouse [Avocent Dell 03R874] on usb-0000:00:1d.1-2
scsi0 : ioc0: LSISAS1068E, FwRev=00142e00h, Ports=1, MaxQ=511, IRQ=169
Vendor: ATA Model: WDC WD1600YS-18S Rev: 6C07
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD1600YS-18S Rev: 6C07
Type: Direct-Access ANSI SCSI revision: 05
Vendor: Dell Model: VIRTUAL DISK Rev: 1028
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 310546432 512-byte hdwr sectors (159000 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 310546432 512-byte hdwr sectors (159000 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:1:0:0: Attached scsi disk sda
libata version 2.21 loaded.
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
GSI 22 sharing vector 0x42 and IRQ 22
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 23 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi1 : ata_piix
scsi2 : ata_piix
ata1: SATA max UDMA/133 cmd 0x000000000001bc30 ctl 0x000000000001bc2a bmdma 0x000000000001bc40 irq 66
ata2: SATA max UDMA/133 cmd 0x000000000001bc38 ctl 0x000000000001bc2e bmdma 0x000000000001bc48 irq 66
ata1.01: ATAPI, max UDMA/33
ata1.01: applying bridge limits
ata1.01: configured for UDMA/33
Vendor: HL-DT-ST Model: DVD-ROM GDR-T10N Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 05
hda: Invalid capacity for disk in drive
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1202361861.095:2): selinux=0 auid=4294967295
tg3.c:v3.80 (August 2, 2007)
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:05:00.0 to 64
input: PC Speaker as /class/input/input4
eth0: Tigon3 [partno(BCM95721) rev 4201 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:19:b9:f9:5e:60
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:06:00.0 to 64
eth1: Tigon3 [partno(BCM95721) rev 4201 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:19:b9:f9:5e:61
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
scsi 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:1:0: Attached scsi generic sg1 type 0
sd 0:1:0:0: Attached scsi generic sg2 type 0
scsi 1:0:1:0: Attached scsi generic sg3 type 5
Uniform CD-ROM driver Revision: 3.20
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr0
floppy0: no floppy controllers found
lp: driver loaded but no devices found
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda1, internal journal
Adding 8385920k swap on /dev/sda2. Priority:-1 extents:1 across:8385920k
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
Fusion MPT misc device (ioctl) driver 3.04.04
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
ADDRCONF(NETDEV_UP): eth0: link is not ready
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
eth0: no IPv6 routers present
ipmi message handler version 39.1
IPMI System Interface driver.
ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca8, slave address 0x20, irq 0
ipmi: Found new BMC (man_id: 0x0002a2, prod_id: 0x0000, dev_id: 0x20)
IPMI kcs interface initialized
ipmi device interface
eth1: no IPv6 routers present
[PageInfo]
LastUpdate: 2008-04-16 18:22:07, ModifiedBy: nabeshin
[Permissions]
view:all, edit:login users, delete/config:doc editors