Linuxの場合は、CPUが1個のみでもNICがリンクアップする。
[ 6.406644] r8169 0000:05:00.0: firmware: agent loaded rtl_nic/rtl8168e-3.fw into memory [ 6.474149] r8169 0000:05:00.0: eth0: link down [ 6.476086] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.028587] r8169 0000:05:00.0: eth0: link up
FreeBSDは物理ディスティネーションモード固定であるようだ。
Forkusr/src/sys/x86/x86/msi.c
#define INTEL_ADDR(msi) \
(MSI_INTEL_ADDR_BASE | (msi)->msi_cpu << 12 | \
MSI_INTEL_ADDR_RH_OFF | MSI_INTEL_ADDR_DM_PHYSICAL)
#define INTEL_DATA(msi) \
(MSI_INTEL_DATA_TRGREDG | MSI_INTEL_DATA_DELFIXED | (msi)->msi_vector)
VM1にCPUを1個のみ割り当てた場合は、リンクアップしました。
Trying to mount root from ufs:/dev/ada0p2 [rw]... re0: link state changed to DOWN re0: link state changed to UP
X Window(gdm)を起動しないようにしても、 VM1にCPUを1個のみ割り当てた場合は、NICがリンクアップしませんでした。
Trying to mount root from ufs:/dev/ada0p2 [rw]... atrtc0: WARNING: Battery failure indication Invalid time in real time clock. Check and reset the date immediately! re0: link state changed to DOWN
VM1にCPUを2個割り当てて、FreeBSDを起動してみた。 NICはMSI-Xが有効になっていた。
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 P
CI Express Gigabit Ethernet Controller (rev 06)
Subsystem: ASRock Incorporation Motherboard (one of many)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 255
Region 0: I/O ports at d000
Region 2: Memory at f0004000 (64-bit, prefetchable)
Region 4: Memory at f0000000 (64-bit, prefetchable)
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3h
ot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L
1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupporte
d-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPe
nd-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L
0 unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive
- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF
Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OB
FF Disabled
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedC
ompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-,
EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizat
ionRequest-
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Not readable
SATAはMSI
06:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: ASRock Incorporation Motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 255
Region 0: I/O ports at c050
Region 1: I/O ports at c040
Region 2: I/O ports at c030
Region 3: I/O ports at c020
Region 4: I/O ports at c000
Region 5: Memory at f7800000 (32-bit, non-prefetchable)
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee06000 Data: 0032
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s, Latency L0 <512ns, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
yuichi_xy への返信
VM1にCPUを2個割り当てて、FreeBSDを起動してみた。 NICはMSI-Xが有効になっていた。
Capabilities: b0 MSI-X: Enable+ Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: d0 Vital Product Data Not readable }}}
メモリ空間のレジスタにも、それっぽい値が設定されていた。
# dd if=/dev/mem bs=1 count=32 iseek=0xf0000000 | hexdump 32+0 records in 32+0 records out 32 bytes transferred in 0.000216 secs (148143 bytes/sec) 0000000 4000 fee0 0000 0000 003b 0000 0000 0000 0000010 e066 11ae d189 7d1a dca2 87ae 0001 0000 0000020
CPUを1個しか割り当てないVM1でLinuxを起動した場合は、NICも使え、xHCIも使える。
CPUを2個割り当てたVM1でFreeBSDを起動して、プロセスをツリー表示してみた。 どこかで、引っかかってしまっているような兆候はみられなかった。
# pstree 0 -w -+= 00000 root [kernel] |-+= 00001 root /sbin/init -- | |--= 00127 root adjkerntz -i | |--= 00483 root /sbin/devd | |--= 00607 root /usr/sbin/syslogd -s | |-+= 00708 root /usr/sbin/sshd | | \-+= 00764 root sshd: yuichi [priv] (sshd) | | \-+- 00767 yuichi sshd: yuichi@pts/0 (sshd) | | \-+= 00768 yuichi -sh (sh) | | \-+= 00846 root su | | \-+= 00847 root _su (csh) | | \-+= 00867 root pstree 0 -w | | \--- 00868 root ps -axwwo user,pid,ppid,pgid,command | |--= 00715 root sendmail: accepting connections (sendmail) | |--= 00718 smmsp sendmail: Queue runner@00:30:00 for /var/spool/clientmqueue | |--= 00722 root /usr/sbin/cron -s | |--- 00755 root /usr/libexec/getty Pc ttyv0 | |--- 00756 root /usr/libexec/getty Pc ttyv1 | |--- 00757 root /usr/libexec/getty Pc ttyv2 | |--- 00758 root /usr/libexec/getty Pc ttyv3 | |--- 00759 root /usr/libexec/getty Pc ttyv4 | |--- 00760 root /usr/libexec/getty Pc ttyv5 | |--- 00761 root /usr/libexec/getty Pc ttyv6 | |--- 00762 root /usr/libexec/getty Pc ttyv7 | \--= 00763 root /usr/libexec/getty std.115200 ttyu0 |--- 00002 root [sctp_iterator] |--- 00003 root [xpt_thrd] |--- 00004 root [pagedaemon] |--- 00005 root [vmdaemon] |--- 00006 root [pagezero] |--- 00007 root [bufdaemon] |--- 00008 root [syncer] |--- 00009 root [vnlru] |--- 00010 root [audit] |--- 00011 root [idle] |--- 00012 root [intr] |--- 00013 root [geom] |--- 00014 root [usb] \--- 00015 root [softdepflush]
top -Pコマンドで各CPUの状態を見てみたが、どちらのCPUでもプロセスが実行されていた。
last pid: 1152; load averages: 0.00, 0.00, 0.00 up 0+01:21:04 22:52:31 22 processes: 1 running, 21 sleeping CPU 0: 0.0% user, 0.0% nice, 0.0% system, 0.0% interrupt, 100% idle CPU 1: 0.0% user, 0.0% nice, 0.0% system, 0.0% interrupt, 100% idle Mem: 14M Active, 18M Inact, 278M Wired, 263M Buf, 4932M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE C TIME WCPU COMMAND 767 yuichi 1 20 0 72136K 5848K select 0 0:08 0.00% sshd 847 root 1 20 0 17564K 3684K pause 0 0:05 0.00% csh 715 root 1 20 0 20340K 4568K select 1 0:02 0.00% sendmail 1152 root 1 20 0 16596K 2392K CPU0 0 0:01 0.00% top 768 yuichi 1 23 0 14536K 2300K wait 0 0:01 0.00% sh 764 root 1 20 0 72136K 5808K select 1 0:01 0.00% sshd 846 yuichi 1 20 0 45324K 2344K wait 0 0:00 0.00% su 607 root 1 20 0 12076K 1744K select 1 0:00 0.00% syslogd 722 root 1 20 0 14176K 1852K nanslp 0 0:00 0.00% cron 757 root 1 20 0 12084K 1716K nanslp 0 0:00 0.00% getty 756 root 1 20 0 12084K 1716K nanslp 0 0:00 0.00% getty 761 root 1 20 0 12084K 1716K nanslp 1 0:00 0.00% getty 762 root 1 20 0 12084K 1716K nanslp 0 0:00 0.00% getty 760 root 1 20 0 12084K 1716K nanslp 0 0:00 0.00% getty 759 root 1 20 0 12084K 1716K nanslp 1 0:00 0.00% getty 755 root 1 20 0 12084K 1716K nanslp 1 0:00 0.00% getty 758 root 1 20 0 12084K 1716K nanslp 1 0:00 0.00% getty 763 root 1 52 0 12084K 1676K ttyin 1 0:00 0.00% getty 483 root 1 20 0 10376K 4432K select 1 0:00 0.00% devd 718 smmsp 1 20 0 20340K 4636K pause 1 0:00 0.00% sendmail 708 root 1 20 0 46876K 5332K select 0 0:00 0.00% sshd 127 root 1 52 0 9952K 1480K pause 1 0:00 0.00% adjkerntz
以下のページを参考に、CPUごとの割り込み発生数が取得できないか試みてみたが、interrupt_sourcesやintrcntはCPUごとに値を管理しているわけではなさそう。
http://people.freebsd.org/~jhb/papers/bsdcan/2008/article/node4.html http://freebsd.1045724.n5.nabble.com/Per-core-per-device-interrupt-counts-td4050285.html
FreeBSDの起動メッセージの差分を比較したところ、次のような違いがありました。
CPU1個
INTR: Adding local APIC 0 as a target Event timer "LAPIC" quality 600 ACPI APIC Table: <BOCHS BXPCAPIC> lapic6: CMCI unmasked APIC: CPU 0 has ACPI ID 0
CPU2個
INTR: Adding local APIC 0 as a target Event timer "LAPIC" quality 600 ACPI APIC Table: <BOCHS BXPCAPIC> Reset cpu 0x6 INTR: Adding local APIC 4 as a target INTR: Adding local APIC 6 as a target FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 4 cpu1 (AP): APIC ID: 6 lapic4: CMCI unmasked APIC: CPU 0 has ACPI ID 0 APIC: CPU 1 has ACPI ID 1
usr/src/sys/x86/x86/intr_machdep.c
/*
* Add a CPU to our mask of valid CPUs that can be destinations of
* interrupts.
*/
void
intr_add_cpu(u_int cpu)
{
if (cpu >= MAXCPU)
panic("%s: Invalid CPU ID", __func__);
if (bootverbose)
printf("INTR: Adding local APIC %d as a target\n",
cpu_apic_ids[cpu]);
CPU_SET(cpu, &intr_cpus);
}
次の内容の /etc/rc.local を作成し、起動直後に割り込みの発生数をシリアルコンソールに出力してみました。
TinyVisorなしでFreeBSDを起動
interrupt total rate irq1: atkbd0 6 0 irq16: ehci0 51 3 irq23: ehci1 117 8 cpu0:timer 3419 244 irq264: xhci0 119 8 irq265: hdac0 78 5 irq266: re0 2 0 irq267: ahci0 823 58 irq268: ahci1 123 8 cpu1:timer 461 32 cpu2:timer 343 24 cpu3:timer 378 27 Total 5920 422
VM1にCPUを2個割り当てFreeBSDを起動
interrupt total rate irq4: uart0 1 0 cpu0:timer 70595 8824 irq264: 1 0 irq265: re0 6 0 irq266: ahci0 1314 164 cpu1:timer 54226 6778 Total 126143 15767
VM1にCPUを1個割り当てFreeBSDを起動 (NIC(re0)の割り込みが1回だけだが発生していました)
interrupt total rate irq4: uart0 1 0 cpu0:timer 6165 43 irq265: re0 1 0 irq266: ahci0 888 6 Total 7055 49
VM1にCPUを1個割り当てて、Linuxを起動し、lspci -vvを実行してみた。
FreeBSDの場合、NICはMSI-Xだが、Linuxの場合、NICもMSIだった。
また、Free BSDの場合Message Dataのビット14(Level)が0だったが、Linuxの場合1だった。しかし、ビット15(Trigger Mode)で0(Edgeモード)を指定しているので、Levelは関係ないはず。
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI E
xpress Gigabit Ethernet controller (rev 06)
Subsystem: ASRock Incorporation Motherboard (one of many)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at f0004000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3h
ot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee06000 Data: 4029
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L
1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupporte
d-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPe
nd-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L
0 unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
No end tag found
Kernel driver in use: r8169
06:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: ASRock Incorporation Device 0612
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: I/O ports at c050 [size=8]
Region 1: I/O ports at c040 [size=4]
Region 2: I/O ports at c030 [size=8]
Region 3: I/O ports at c020 [size=4]
Region 4: I/O ports at c000 [size=32]
Region 5: Memory at f7800000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee06000 Data: 4041
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s, Latency L0 <512ns, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Kernel driver in use: ahci
yuichi_xy への返信
FreeBSDの場合、NICはMSI-Xだが、Linuxの場合、NICもMSIだった。
more /boot/loader.conf.local に以下の行を追加し、MSI-Xを無効化し、MSIを有効化してみた。
hw.re.msix_disable=1
それでも、NICがリンクアップしなかった。
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port 0xd000-0xd0f f mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff at device 0.0 on pci5 re0: MSI count : 1 re0: MSI-X count : 4 re0: attempting to allocate 1 MSI vectors (1 supported) msi: routing MSI IRQ 265 to local APIC 6 vector 59 re0: using IRQ 265 for MSI re0: Using 1 MSI message re0: Chip rev. 0x2c800000 re0: MAC rev. 0x00000000 miibus0: <MII bus> on re0 rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 rgephy0: OUI 0x00e04c, model 0x0011, rev. 5 rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX , 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX- master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re0: bpf attached re0: Ethernet address: bc:5f:f4:97:58:96 ... start_init: trying /sbin/init re0: link state changed to DOWN FreeBSD/amd64 (xxxxx) (ttyu0) login:
if_re.cに定義されている他のパラメータも試してみたが、NICがリンクアップしない事象が発生した。
hw.re.intr_filter=1
hw.re.prefer_iomap=1
r144でも再現しました。
r193とFreeBSD 10.0の組み合わせでも発生しました。
r279とFreeBSD 10.0の組み合わせでも再現しました。
r346とFreeBSD 10.2の組み合わせでも再現しました。
25b1818336f9 と FreeBSD 10.2の組み合わせでは、問題は発生しませんでした。
つまり、VM1にCPUを1個しか割り当てずにVM1でFreeBSDを起動しても、NICがリンクアップしました。
yuichi_xy への返信
25b1818336f9 と FreeBSD 10.2の組み合わせでは、問題は発生しませんでした。 つまり、VM1にCPUを1個しか割り当てずにVM1でFreeBSDを起動しても、NICがリンクアップしました。
release 1.7 (84802a6df98c)と FreeBSD 10.2の組み合わせでも、問題は発生しませんでした。 いつの間にか発生しなくなってしまったようです。
チケットの状態は完了にします。
障害発生リビジョン: r118